PROHLÁŠENÍ O VLASTNOSTECH

Transkript

1 PROHLÁŠENÍ O VLASTNOSTECH DoP: 0125 pro kotva pro vysoká zatíže í fis her FHB (Lepená kotva pro použití v eto u) CS 1. Jedi eč ý ide tifikač í kód typu výro ku: DoP: )a ýšle é/za ýšle á použití: Dodateč é upev ě í v taže é a tlače é zó ě eto u, viz. dopl ěk, o zvláště Přílohy B 1 - B 4 3. Výrobce: fischerwerke GmbH & Co. KG, Klaus-Fischer-Straße 1, Waldachtal, Ně e ko 4. )pl o o ě ý zástup e: Systém/systémy POSV: 1 6. Evropský dokument pro posuzování: ETAG 001; Evropské technické posouzení: ETA-06/0171; Subjekt pro technické posuzování: DIBt Oznámený subjekt/oznámené subjekty: 1343 MPA Darmstadt 7. Deklarovaná vlastnost/deklarované vlastnosti: Mechanická odolnost a stabilita (BWR 1), Bezpeč ost při použití (BWR 4) Charakteristická únosnost: Viz. dopl ěk, o zvláště Přílohy C 1 - C 3 Posu y při zatíže í tahe a s yke : Viz. dodatek, o zvláště Příloha C 3 Bezpeč ost v případě požáru (BWR 2) Odolnost proti ohni: Kotve í splňuje požadavky Třídy A 1 Požár í odol ost: VNS 8. Přísluš á te h i ká doku e ta e a/ e o spe ifi ká te h i ká doku e ta e: --- Vlast osti výše uvede ého výro ku jsou ve shodě se sou ore deklarova ý h vlast ostí. Toto prohláše í o vlast oste h se v souladu s aříze í EU č. 5/ vydává a výhrad í odpověd ost výro e uvede ého výše. Podepsáno za výrobce a jeho jménem: Andreas Bucher, Dipl.-Ing. Wolfgang Hengesbach, Dipl.-Ing., Dipl.-Wirtsch.-Ing. Tumlingen, Toto PoV ylo připrave o v růz ý h jazykový h uta í h.. V případě rozporu vždy rozhoduje i terpreta e verze v anglickém jazyce. - Příloha o sahuje epovi é a doplňkové i for a e v a gli ké jazy e a rá e záko ý h požadavků.

2 Appendix 1 / 11 Specific Part 1 Technical description of the product The fischer Highbond-anchor FHB is a torque controlled bonded anchor consisting of a mortar cartridge with FIS HB and an anchor rod with hexagon nut and washer. The anchor rod (including nut and washer) is made of galvanised steel. The load transfer is realised by mechanical interlock of several cones in the bonding mortar and then via a combination of bonding and friction forces in the anchorage ground (concrete). The product description is given in Annex A. 2 Specification of the intended use in accordance with the applicable European Assessment Document The performances given in Section 3 are only valid if the anchor is used in compliance with the specifications and conditions given in Annex B. The verifications and assessment methods on which this European Technical Assessment is based lead to the assumption of a working life of the anchor of at least 50 years. The indications given on the working life cannot be interpreted as a guarantee given by the producer, but are to be regarded only as a means for choosing the right products in relation to the expected economically reasonable working life of the works. 3 Performance of the product and references to the methods used for its assessment 3.1 Mechanical resistance and stability (BWR 1) Essential characteristic Performance Characteristic resistance See Annex C 1 to C 3 Displacements under tension and shear loads See Annex C Safety in case of fire (BWR 2) Essential characteristic Reaction to fire Resistance to fire Performance Anchorages satisfy requirements for Class A1 No performance assessed 3.3 Hygiene, health and the environment (BWR 3) Regarding dangerous substances there may be requirements (e.g. transposed European legislation and national laws, regulations and administrative provisions) applicable to the products falling within the scope of this European Technical Assessment. In order to meet the provisions of Regulation (EU) No 305/2011, these requirements need also to be complied with, when and where they apply. 3.4 Safety in use (BWR 4) The essential characteristics regarding Safety in use are included under the Basic Works Requirement Mechanical resistance and stability.

3 Appendix 2 / 11 4 Assessment and verification of constancy of performance (AVCP) system applied, with reference to its legal base In accordance with guideline for European technical approval ETAG 001, April 2013, used as European Assessment Document (EAD) according to Article 66 Paragraph 3 of Regulation (EU) No 305/2011, the applicable European legal act is: [96/582/EC]. The system to be applied is: 1

4 Appendix 3 / 11

5 Appendix 4 / 11

6 Appendix 5 / 11

7 Appendix 6 / 11

8 Appendix 7 / 11

9 Appendix 8 / 11

10 Appendix 9 / 11

11 Appendix 10 / 11

12 Appendix 11 / 11