PROHLÁŠENÍ O VLASTNOSTECH č. 0031 CS 1. Jedi eč ý ide tifikač í kód typu výro ku: natloukací kotva fischer FNA II 2. )a ýšle é/za ýšle á použití: Výrobek Kovové kotvy do betonu pro lehké zátěže Za ýšle é/za ýšle á použití Pro použití v redu da t í h systé e h pro upev ě í a/ e o zavěše í k eto ový prvků jako lehké strop í podhledy e o i stala e., viz. dopl ěk, o zvláště Přílohy B 1 - B 2 3. Výrobce: fischerwerke GmbH & Co. KG, Klaus-Fischer-Straße 1, 72178 Waldachtal, Ně ecko 4. )pl o o ě ý zástup e: -- 5. Systém/systémy POSV: 2+ 6a. Harmonizovaná norma: --- Oznámený subjekt/oznámené subjekty: --- 6b. Evropský dokument pro posuzování: ETAG 001; 2016-04 Evropské technické posouzení: ETA-06/0175; 2016-10-28 Subjekt pro technické posuzování: DIBt Oznámený subjekt/oznámené subjekty: 1343 MPA Darmstadt 7. Deklarovaná vlastnost/deklarované vlastnosti: Mechanická odolnost a stabilita (BWR 1) Základní vlastnosti Výkon Charakteristické hodnoty Viz. dodatek, o zvláště Příloha C 1 Bezpeč ost v případě požáru (BWR 2) Základní vlastnosti Výkon Odolnost proti ohni Kotve í splňuje požadavky Třídy A Požár í odol ost Viz. dodatek, o zvláště Příloha C 2 Bezpeč ost při použití (BWR 4) Základní vlastnosti Výkon Charakteristická únosnost v tahu a ve smyku viz. dopl ěk, o zvláště Příloha C 1 8. Přísluš á te h i ká doku e ta e a/ e o spe ifi ká te h i ká doku e ta e: --- Vlast osti výše uvede ého výro ku jsou ve shodě se sou ore deklarova ý h vlast ostí. Toto prohláše í o vlast oste h se v souladu s aříze í EU č. 5/ vydává a výhrad í odpověd ost výro e uvede ého výše. Podepsáno za výrobce a jeho jménem: Andreas Bucher, Dipl.-Ing. Wolfgang Hengesbach, Dipl.-Ing., Dipl.-Wirtsch.-Ing. Tumlingen, 2016-11-04 - Toto PoV ylo připrave o v růz ý h jazykový h uta í h.. V případě rozporu vždy rozhoduje i terpreta e verze v anglickém jazyce. - Příloha o sahuje epovi é a doplňkové i for a e v a gli ké jazy e a rá e záko ý h požadavků.
Appendix 1 / 7 Specific Part 1 Technical description of the product The fischer nail anchor FNA II is an anchor made of galvanised steel, stainless steel (marking "A4") or high corrosion resistant steel (marking "C") which is pushed into a drilled hole and expanded by loading. The product description is given in Annex A. 2 Specification of the intended use in accordance with the applicable European Assessment Document The performances given in Section 3 are only valid if the anchor is used in compliance with the specifications and conditions given in Annex B. The verifications and assessment methods on which this European Technical Assessment is based lead to the assumption of a working life of the anchor of at least 50 years. The indications given on the working life cannot be interpreted as a guarantee given by the producer, but are to be regarded only as a means for choosing the right products in relation to the expected economically reasonable working life of the works. 3 Performance of the product and references to the methods used for its assessment 3.1 Mechanical resistance and stability (BWR 1) The essential characteristics regarding Mechanical resistance and stability are included under the Basic Works Requirement Safety in use. 3.2 Safety in case of fire (BWR 2) Essential characteristic Performance Reaction to fire Resistance to fire See Annex C 2 3.3 Safety in use (BWR 4) Essential characteristic Anchorages satisfy requirements for Class A1 Performance Characteristic resistance for all load directions See Annex C 1 4 Assessment and verification of constancy of performance (AVCP) system applied, with reference to its legal base In accordance with guideline for European technical approval ETAG 001, April 2013 used as European Assessment Document (EAD) according to Article 66 Paragraph 3 of Regulation (EU) No 305/2011 the applicable European legal act is: [97/161/EC]. The system to be applied is: 2+
Appendix 2 / 7
Appendix 3 / 7
Appendix 4 / 7
Appendix 5 / 7
Appendix 6 / 7
Appendix 7 / 7