CZ EN Quick Start Guide Clear Rychlý průvodce nastavením
Measurement Měření Před Fully prvním charge použitím the blood plně pressure dobijte monitor baterii before přístroje. first use. 1 Rest your bare (or thinly clothed) left arm flat on a table. Položte levou paži na stůl. 2 Place Navlečte cuff over manžetu left arm so na the levou cuff tubing paži is tak, centered aby on vývod the hadičky inside of your z manžety arm and aligned byl uprostřed with your paže middle a finger. směřoval k prostřednímu prstu. Zarovnejte Note the direction manžetu of the tak, aby cuff vývod tubing hadičky and alignment směřoval k with vašemu your prostředníčku. middle finger.
3 The Spodní bottom okraj of the manžety cuff should umístěte be about 1-2 1/2" cm above nad your loketní ohyb. elbow. Tighten Mezi the manžetou cuff firmly, a leaving paží about ponechte 1 finger space. prostor přibližně na jeden prst. 1/2 inch (1-2 cm) 4 Vložte Insert cuff plastovou tubing connector koncovku into blood hadičky pressure do tlakoměru monitor a přístroj unit, and the se automaticky monitor will power spustí. on automatically. Ujistěte Make sure se, to že fully je koncovka insert the hadičky cuff tubing správně connector připojena into k the tlakoměru. blood pressure monitor.
5 Jakmile se přístroj poprvé spustí, zvolte You You will will need need to to select your your language language after after turning turning on on the the monitor požadovaný monitor for for the the jazyk. first first time. time. English Français Deutsch Italiano Press Stiskněte to change pro změnu language jazyka Press Stisk něte to confirm pro language potvrzení jazyka 6 Pro spuštění měření znovu stiskněte tlačítko Press User or User button again to start a measurement. Press Press uživatele User 1 any button jedna, or User to stop nebo 2 button measurement dvě. again to start a measurement. and to turn off the Press monitor. any button to stop a measurement and to turn off the monitor. Stiskněte kterékoliv tlačítko pro zastavení měření a vypnutí přístroje. During Během the měření measurement, ucítíte, jak you se will manžeta feel the obepíná cuff tightening kolem During around vaší paže. the your Zůstaňte measurement, arm. Remain v klidu still you a nehýbejte and will feel do not the s move paží, cuff tightening dokud your arm se around until měření the your nedokončí. measurement arm. Remain is complete. still and do not move your arm until the measurement is complete.
Nastavení Wireless bezdrátové Network Setup sítě 1 Otevřete Go to the Apple App Store nebo or Google Google Play Store Play and a stáhněte search si "ihealth aplikaci MyVitals." ihealth Download MyVitals. the app Vytvořte and then si log uživatelský in. účet a přihlaste se. 2 Stiskněte Press and hold a držte the User tlačítko 2 button uživatele for 10 seconds 2 po until dobu the 10 sekund, screen displays dokud the select displej language nezobrazí page možnost volby jazyka. English Français Deutsch Italiano Press Stiskněte to change pro změnu language jazyka Stisk Press něte to confirm pro potvrzení language jazyka
3 The Poté screen displej will zobrazí display the nastavení wireless network pro bezdrátovou setup page. síť. Launch Spusťtě the ihealth aplikaci MyVitals ihealth app, go MyVitals, to Select New otevřete Devices and choose Clear (BPM1). Follow the on-screen instructions to nastavení finish setting nového up your zařízení wireless network. a vyberte Clear (BPM1). Postupujte podle instrukcí a dokončete nastavení bezdrátové sítě. Connecting WiFi... Ready to connect, launch MyVitals app. Setup complete! Nastavení Your kompletní! blood pressure Váš measurements tlakoměr automaticky will automatically odesílá naměřené údaje do aplikace ihealth upload to the ihealth MyVitals app. MyVitals