MG-6-2 PEGAS 60 MIG SYN_MAN SERVICE MANUAL page SERVISNÍ MANUÁL PEGAS 60 MIG SYN/MAN SERVICE MANUAL PEGAS 60 MIG SYN/MAN. VAROVÁNÍ WARNING UPOZORNĚNÍ Pouze osoba splňující kvalifikaci danou zákonem je oprávněna opravovat stroj. PŘED OTEVŘENÍM KRYTU STROJE JEJ ODPOJTE VYTAŽENÍM SÍŤOVÉ VIDLICE ZE SÍTĚ. Každé 4 měsíce otevřete stroj a jemně ho vyfoukejte stlačeným suchým vzduchem POZOR, NEPOUŽÍVEJTE STLAČENÝ VZDUCH O PŘÍLIŠ VYSOKÉM TLAKU, ABY NEDOŠLO K MECHANICKÉMU POŠKOZENÍ ELEKTROSOUČÁSTEK. Každé 4 měsíce zkontrolujte řádný stav svařovacích kabelů a síťových kabelů. Není povolena žádná modifikace svařovacího stroje. Pro Vaši bezpečnost je nutné posečkat se sundáním krytu ze stroje po odpojení ze sítě po dobu minimálně 5 minut, kdy klesne napětí na kondenzátorech na hodnotu pod 36 V. NOTE Only trained personnel are permitted to work inside the machine. BEFORE OPENING THE MACHINE, CUT OFF ITS ELECTRICAL POWER BY REMOVING THE PLUG FROM THE MAINS SUPPLY SOCKET. Every six months, open the machine and clean it inside, using compressed dehumidified air. CAUTION. DO NOT USE COMPRESSED AIR AT TOO HIGH A PRESSURE. YOU COULD DAMAGE THE ELECTRONIC COMPONENTS. With the same frequency, check the welding cables and the supply cables. No modification, of any type, may be made to the welding machine. For safety while maintaining the machine, please shut off the supply power and wait for 5 minutes, until capacity voltage already drops to safe voltage 36V. 2. BLOKOVÉ SCHÉMA ELECTRICAL PRINCIPLE DRAWING
- MG-6-2 PEGAS 60 MIG SYN_MAN SERVICE MANUAL page 2 AC AC2 GDN 3 AC AC Fan G A S + -24V 4 2 Switch Power Supply N T C QD2 QD ZBYQ OC OC2 Motor PCB Control PCB OUT+ OUT- 3. NÁHRADNÍ DÍLY SPARE PARTS
MG-6-2 PEGAS 60 MIG SYN_MAN SERVICE MANUAL page 3 Po s. Item No Popis Description Quantit y 8.253.020 Držák - madlo P250 Handle P250 2 8.050.2 Kryt horní P60MIG Cover upper P60MIG 3 8.068.984 Panel zadní P60MIG Back Panel P60MIG 4 7.232.730 Vypínač hlavní P60MIG Switch ON/OFF P60MIG 5 8.462.6 Konektor vzduch P40 Air Connector P40 6 8.83.00 Box P60MIG Box P60MIG 7 7.720.005-B Ventilátor P60MIG Fan P60MIG 8 8.24.623 Panel střední P60MIG Midle front P60MIG 9 5.496.067 EMC P60MIG EMC P60MIG 0 7.624.28 "Y" konektor P60MIG "Y" Connector P60MIG
MG-6-2 PEGAS 60 MIG SYN_MAN SERVICE MANUAL page 4 8.23.59-B Držák ventilů P60MIG Holder valves P60MIG 2 7.253.03 Ventil Pegas Solenoid Valve Pegas 2 3 6.85.9 Trafo hlavní P60MIG Main transformer P60MIG 4 8.23.620 Držák panelu P40 Holder front P40 5 7.4.00 Usměrňovač PEGAS 60 E Rectifier Bridge 6 5.496.996-E PCB řídící P60MIG-SYN PCB Control P60MIG-SYN 6 5.496.996-C PCB řídící P60MIG-MAN PCB Control P60MIG-MAN 7 8.425.9 Chladič 2 P60MIG Heat sink 2 P60MIG 8 7.425.63 Tranzistor IGBT Discrete P40 Discrete IGBT P40 4 9 8.425.20 Chladič 3 P60MIG Heat sink 3 P60MIG 20 7.503.530 Držák PCB P60MIG Holder PCB P60MIG 4 2 3.200.2 PCB hlavní P60MIG Main board P60MIG PCB silová P60MIG kompl. PCB Power P60MIG compl. 2 5.AAA.P60 (Obsahuje položky (Containsitems MIG 3+4+5+7+8+9+20+2+22+ 3+4+5+7+8+9+20+2+22 23+24+25+27+4+42 ) +23+24+25+27+4+42 ) 2 5.AAR.P60 MIG PCB silová P60MIG kompl. Repas(Obsahuje položky 3+4+5+7+8+9+20+2+22+ 23+24+25+27+4+42 ) 22 8.23.633 Držák PCB hlavní P60MIG PCB Power P60MIG compl. Repair (Containsitems 3+4+5+7+8+9+20+2+22 +23+24+25+27+4+42 ) Holder for PCB Main board P60MIG 23 7.32.05 Sonda Hall CUT P60MIG 300A Hall CUT P60MIG 300A 24 7.42.07 Dioda PEGAS 30 E Diode Pegas 30E 8 25 7.445.40 NTC K45 47K NTC K45 47K 26 7.456.26 Potenciometer P60MIG Potenciometer P60MIG 27 8.425.8 Chladič P60MIG Heat sink P60MIG 28 5.057 Posuv Pegas MIG Feeder Pegas MIG complete PCB přední P60MIG-SYN PCB Front P60MIG-SYN 29 5.495.994-B (obsahuje položky 29+45) (Containsitems 29+45) PCB přední P60MIG-MAN PCB Front P60MIG-MAN 29 5.496.062 (obsahuje položky 29+45) (Containsitems 29+45) 30 8.069.984 Panel přední P60MIG Front plastic panel P60MIG Panel P60MIG-SYN plech Front Panel P60MIG-SYN 3 8.306.5-S metal sheet 3 8.03.40-B Folie P60MIG-SYN Front Panel Film P60MIG-SYN Panel P60MIG-MAN plech Front Panel P60MIG-MAN 3 8.306.5-M metal sheet 3 8.306.2 Folie P60MIG-MAN Front Panel Film P60MIG-MAN 32 7.32.303 Konektor Pegas panelová zásuvka (samec) PEGAS nižšího výrobního čísla než 00055294 3-PIN Pegas socket connector (male) PEGASES of lower serial No that 00055294 2
MG-6-2 PEGAS 60 MIG SYN_MAN SERVICE MANUAL page 5 32 7.32.303- Konektor Pegas panelová zásuvka (samice) PEGAS vyššího výrobního čísla než 00055293 3-PIN Pegas socket connector (female) PEGASES of higher serial No that 00055293 33 8.78.0 Konektor euro P60MIG Connector EURO P60MIG 34 7.52.35 Rychlospojka P60MIG 35-70 Quick Connector P60MIG 35- plyn 70 gas 35 8.055.8 Kryt spodní P60MIG Ground P60MIG 36 8.462.8 Záměnný konektor P60MIG CHANGEOVER CONNECTOR 2 37 8.08.0 Tělo posuvu s ramenem pro Pegas 60 MIG bez kladky P60MIG Wire feeder body with arm for Pegas 60 MIG (without rool) 38 8.99.30 Držák cívky P60MIG Spool Holder P60MIG 39 8.05.2 Kryt boční P60MIG Lateral Cover P60MIG 40 7.686.300 Zámek P60MIG Lock P60MIG 4 6.27.32 Ferit P60MIG Ferit P60MIG Kondenzátor P60MIG Capacitor P60MIG 42 4343 6 000mikroF/250V 000mikroF/250V 43 4.02.008-A Kladka 0.8-.0 P60MIG Roll 0.8-.0 P60MIG 44 7.52.33 Rychlospojka Pegas 35-70 Quick Connector Pegas 35-70 45 7.456.48 Potenciometr 0K Potenciometer 0k 3 4. ZÁVADY - ŘEŠENÍ Závada Příčina Řešení Stroj je zapnutý, ventilátor funguje, LED zapnutí nesvítí LED nebo její připojení je vadné. Opravte připojení nebo vyměňte PCB přední P60MIG- SYN Opravte připojení nebo vyměňte PCB přední P60MIG- MAN Stroj je zapnutý, LED zapnutí svítí, ventilátor neběží. Stroj je zapnutý, LED zapnutí nesvítí, ventilátor neběží. Silová PCB je vadná. Překážka rotace ventilátoru. Motor ventilátoru poškozen. Není napětí v síti Přepětí nebo podpětí v síti. Opravte nebo vyměňte PCB Power P60MIG kompl. Odstraňte Vyměňte ventilátor Zkontrolujte, jestli je v síti napětí. Zkontrolujte síťové napětí. Žádné napětí na prázdno Závada generátoru. Zkontrolujte hlavní obvod AC a AC2 Svařovací kabely nejsou připojeny do konektorů. Připojte svařovací kabely do rychlospojek na stroji. Poškozený svařovací kabel. Vyměňte nebo opravte svařovací kabel. Žádný svařovací proud na svorkách Zemnící kabel není připojen nebo je špatně připojen. Zkontrolujte zemnící kabel Obtížně se zapaluje oblouk nebo dochází k lepení elektrody. Špatně utažené svařovací kabely. Zkontrolujte utažení svařovacích kabelů.
MG-6-2 PEGAS 60 MIG SYN_MAN SERVICE MANUAL page 6 Nestabilní svařovací oblouk. Svařovací proud nelze nastavit. Penetrace tavné lázně nedostačující. Svařenec je znečištěn olejem nebo prachem. MMA/TIG výběr je špatný. ARC FORCE nastaveno příliš nízké. Poškozený potenciometr předního panelu. Svařovací proud je nastaven příliš nízko. ARC FORCE nastaveno příliš nízké. Nepříznivý vliv průvanu Excentrická elektroda Očistěte svařenec. Vyberte MMA svařování. Zvyšte ARC FORCE. Opravte nebo vyměňte potenciometr. Zvyšte svařovací proud Zvyšte ARC FORCE. Použijte zástěnu. Změňte úhle uchycení elektroda Vyměňte elektrodu Nahněte elektrodu proti směru magnetického vlivu. Nestabilní oblouk Vliv magnetismu Změňte pozici zemnícího kabelu nebo přidejte zemnící kabel na opačnou stranu svařence. Přehřátí Stroj zatížen příliš Počkejte, až se stroj vychladí LED ALARM svítí Ochrana přepětí Nestandardní proud na hlavním obvodu. Otestujte a opravte hlavní obvod PCB Power P60MIG kompl. TROUBLESHOOTING Troubles Reasons Solutions Turn on the power source, and fan works, but the power light is not on. Turn on the power source, and the power light is on, but fan doesn t work The power light damaged or connection is not good Power PCB failures There is something in the fan The fan motor damaged No input voltage Test and repair the inside circuit of power light PCB Front P60MIG-SYN Test and repair the inside circuit of power light PCB Front P60MIG-MAN Repair or change power PCB Power P60MIG compl. Clear out Change fan motor Check whether there is input voltage Turn on the power source, and the power light is not on, and fan doesn t work No no-load voltage output No current output in the welding Overvoltage (Input voltage is too much or not) There is trouble inside the machine Welding cable is not connected with the two output of the welder. Welding cable is broken Check input voltage Check the main circuit, AC and AC2 Connect the welding cable to the welder s output Wrap, repair or change the welding cable
MG-6-2 PEGAS 60 MIG SYN_MAN SERVICE MANUAL page 7 Not easy to start arc in the welding, or easy to cause sticking Earth cable is not connected or loosen The plug loosen or connect not well Oil or dust covered the workpiece MMA/TIG welding selection is wrong Check the earth clamp Check and tighten the plug Check and clear out Selecting the MMA welding The arc is not stable in the welding process The arc force is too small Increase the arc force The welding current The welding current can not be potentiometer in the front adjusted panel connection not so Repair or change the potentiometer good or damaged The welding current Increase the welding current The penetration of molten pool is not enough(mma) adjusted too low The arc force adjusted too small Increase the arc force Airflow disturbance The electrode eccentricity Use the shelter from airflow Adjust the electrode angle Change the electrode Arc blow Incline the electrode to the opposite way of the magnetic blow Magnetic effect Change the position of earth clamp or add earth cable in the two side of workpiece Use the short arc operation The alarm light is on Over heat protection Over current protection Over welding current Working time too long Unusual current in the main circuit Induce the welding current output Induce the duty cycle (interval work) Test and repair the main circuit and drive PCB Power P60MIG compl. 5. KONTROLA SILOVÉ PCB CHECKING THE POWER PCB Nástroj: standardní multimetr nastavený do pozice kontrola diod. Všechny komponenty proměřte nejdříve podle řádku tabulky a po té podle řádku 2. Tool: standard multimeter set to the position Diode Measure all the components firstly according line and then according line 2 of the table. 5. Měření tranzistorů T, T2, T4 a T5 Checking the transistors T, T2, T4 and T5
MG-6-2 PEGAS 60 MIG SYN_MAN SERVICE MANUAL page 8 Line Červený hrot/red tester Černý hrot/black tester Hodnota/Value G E 0,20-0,30 2 E G 0,20-0,30 Pokud je jakákoli naměřená hodnota mimo uvedený rozsah, je potřeba vyměnit vždy celý pár tranzistorů (T-T2 nebo T4-T5).. Součástku odletujte z PCB, 2. odšroubujte z chladiče, 3. odstraňte cín odsátím z otvorů PCB 4. očistěte chladič od teplovodné pasty lihem, 5. naneste teplovodnou pastu na novou součástku, 6. přišroubujte k chladiči 7. a zaletujte součástku k PCB It is always necessary to exchange a complete couple of transistors (T-T2 or T4- T5) if any measured value is out of the range.. Unsolder the component from the PCB, 2. unscrew that from the heat sink, 3. suck away the tin from the holes in the PCB 4. wipe off the heat transmitting paste from the heat sink by means of spirit 5. spread on the new component the heat transmitting paste, 6. screw the new component on the heat sink, 7. solder the new component on the PCB
MG-6-2 PEGAS 60 MIG SYN_MAN SERVICE MANUAL page 9 5.2 Měření diod D až D8 Checking the diodes D D8 Line Červený hrot/red tester Černý hrot/black tester Hodnota/Value A K 0,30-0,37 2 K A OL Pokud je jakákoli naměřená hodnota mimo uvedený rozsah je potřeba vyměnit vždy celý pár diod (D-D2, D3-D4, D5-D6 nebo D7-D8).. Součástku odletujte z PCB, 2. odšroubujte z PCB, 3. odstraňte cín odsátím z otvorů PCB 4. očistěte PCB od teplovodné pasty lihem, 5. naneste teplovodnou pastu na novou součástku, 6. přišroubujte k PCB 7. a zaletujte součástku k PCB It is always necessary to exchange a complete couple of diodes (D-D2, D3-D4, D5-D6 or D7-D8) if any measured value is out of the range.. Unsolder the component from the PCB, 2. unscrew that from the PCB, 3. suck away the tin from the holes in the PCB 4. wipe off the heat transmitting paste from the PCB by means of spirit 5. spread on the new component the heat transmitting paste, 6. screw the new component on the PCB, 7. solder the new component on the
MG-6-2 PEGAS 60 MIG SYN_MAN SERVICE MANUAL page 0 6. DOPORUČENÉ NÁHRADNÍ DÍLY NA SKLAD NA 00 KS ZAKOUPENÝCH PEGAS 60 MIG SYN/MAN PCB RECOMEDED QUANTITY OF SPARE PARTS FOR 00 PCS OF PURCHASED PEGAS 60 MIG SYN/MAN Kod Název Description Quantity 7.42.07 Dioda PEGAS 30 E Diode Pegas 30E 2 5.AAA.P60MIG PCB silová P60MIG kompl. PCB Power P60MIG compl. 2 7.425.63 Tranzistor IGBT Discrete P40 Discrete IGBT P40 20 4343 Kondenzátor P60MIG Capacitor P60MIG 2 000mikroF/250V 000mikroF/250V 5.495.994-B PCB přední P60MIG-SYN PCB Front P60MIG-SYN 2 (obsahuje položky 29+45) (Containsitems 29+45) 5.496.062 PCB přední P60MIG-MAN PCB Front P60MIG-MAN 2 (obsahuje položky 29+45) (Containsitems 29+45) 5.496.996-E PCB řídící P60MIG-SYN PCB Control P60MIG-SYN 2 5.496.996-C PCB řídící P60MIG-MAN PCB Control P60MIG-MAN 2 7.445.40 NTC K45 47K NTC K45 47K 2 7.4.00 Usměrňovač PEGAS 60 E Rectifier Bridge 4 7.720.005-B Ventilátor P60MIG Fan P60MIG 6 7.232.730 Vypínač hlavní P60MIG Switch ON/OFF P60MIG 4 7.32.05 Sonda Hall CUT P60MIG 300A Hall CUT P60MIG 300A 4 8.462.6 Konektor vzduch P40 Air Connector P40 4 Worked out: DJ 2/3/20 Inspected: DJ 7//20 Approved: DJ 7//20