manufacturer and supplier of products for electromagnetic testing of materials www.indetec.cz
EDDY CURRENT APPLICATIONS IN AVIATION APLIKACE V LETECTVÍ - METODA VÍŘIVÝCH PROUDŮ Povrchové zkoušení a zkoušení vícevrstvých konstrukcí Eddy Current Surface and Multi-Layered Testing - zkoušení potahových plechů, nýtových spojů, šroubových spojů - zjišťování výrobních a provozních vad (únavové trhliny, vměstky, důlková koroze atd.) - skin metal sheets testing, rivet joints and screwed joints testing - manufacturing and in-service defects detection (fatigue cracks, inclusions, pitting etc.) Kontrola otvorů rotačními sondami Bolt-Hole Eddy Current Inspection - otvory závěsů křídlo/trup, klapek, motorů, pylonů - otvory nýtových spojů, šroubových spojů a hi-lock spoje - the holes of the wing-fuselage attachment fittings, flap, engine and pylon fittings - the holes of the rivet joints, screwed joints and hi-locks Zkoušení vodivých a nevodivých povlaků Conductive and non-conductive coatings testing Měření vodivosti Conductivity testing Třídění hliníkových slitin Aluminium alloy sorting Kontrola svarů Weld testing EC signál - povrchová trhlina EC signal - surface crack EC signál - trhlina ve vícevrstvých nýtových spojích EC signal - crack in multi-layered rivet joints structure EC signál - EDM drážky EC signal - EDM notches EC signál - vměstky EC signal - inclusions
EDDY CURRENT INSPECTION OF CARBON FIBER COMPOSITE MATERIALS Introduction The failures resulting from impact or fatigue load occur in composite structures. At different applications, especially in aviation, while non-destructive inspection of carbon fiber reinforced plastic composite may occur some troubles that arise from the limitations of individual NDT method. Development of advanced diagnostic systems that are able easily to identify and detect the degradation of the material is a new challenge for the NDI. Equipment An INDETEC composite probe has been developed for the inspection of the carbon fiber composite material. It is an high-frequency and narrowband transducer, which allows the detection of imperfections within a frequency range from 8.5 MHz to 10 MHz. The coils are wound on a ferrite core and arranged crosswise and connected to driver/pick up mode. Type of material: Carbon fiber texture in epoxy resin Carbon fiber reinforced plastic (CFRP) Carbon fiber reinforced polymer (CRP) Carbon fiber reinforced thermoplastic (CFRTP) Unidirectional carbon fiber prepreg etc. Type of Discontinuities: Artificial flaw (notch, hole), delamination, wave, missing bundles, cracks, fractures, carbon fiber breaking, detection of fiber direction. Carbon fiber texture: EC signal without failure EC signal - wave EC signal - notch EC signal - hole EC signal without failure Carbon fiber prepreg EC signal - delamination Carbon fiber prepreg EC signal without failure CFRP EC signal - defect CFRP
EDDY CURRENT APPLICATIONS IN POWER INDUSTRY APLIKACE V ENERGETICE - METODA VÍŘIVÝCH PROUDŮ Kontrola výměníkových trubek Kontrola parogenerátoru Kontrola tlakových nádob Kontrola turbín Heat exchanger tube inspection Steam generator inspection Reactor pressure vessel inspection Turbine inspection Detekce výrobních a provozních nespojitostí (podélné/příčné trhliny, praskliny, vměstky, důlková koroze, napěťová a plošná koroze, promáčknutí, eroze atd.) Detection of manufacturing and in-service defects (longitudinal/transversal cracks, fractures, inclusions, pitting, stress and general corrosion, dent, erosion etc.) Bobbin sondy - ohebné včetně středicích perel pro lepší kontrolu Bobbin probes - flexible including centering beads for better inspection EC signál - umělé vady (otvor skrz, úbytek stěny trubky, vnitřní a vnější zápich) EC signal - artificial flaw (through hole, wall loss, internal and external groove)
EDDY CURRENT APPLICATIONS IN OTHER INDUSTRIES APLIKACE V OSTATNÍM PRŮMYSLU - METODA VÍŘIVÝCH PROUDŮ Automobilový průmysl Železniční průmysl Petrochemický průmysl Strojírenský průmysl Automotive industry Railway industry Petrochemical industry Engineering industry Přístrojové kabely, adaptéry / Transducer cables, adapters Kalibrační vzorky / Calibration standards
INDETEC ndt, s.r.o. Na Bělidle 926 430 01 Chomutov Czech Republic phone: +420 474 651 820 web: www.indetec.cz