SL20P HORIZONTÁLNÍ ŽALUZIE česky Technický Katalog ScreenLine rámezek 20 mm
HORIZONTÁLNÍ ŽALUZIE SL20P Horizontální žaluzie použitá u ScreenLine SL20P systému je vyrobena podle náročných technických specifikací a výrobních standardů. Ovládání horizontální žaluzie je docíleno pomocí otočného magnetického přenosu přes speciální rožek, jež zaručuje hermetické uzavření jednotky ve skle. Naklápění se děje pomocí pružné spojky ovládané pomocí otočného knoflíku na rámu okna. Spodní profil žaluzie je pomocí kolíčků zajištěn v bočním vedení což umožňuje otáčet žaluzii o 180 stupňů. Výška 300 ~ 2.500 mm Šířka 220 ~ 2.000 mm Max. plocha 2 m 2 P rozměry technické údaje SL20P Systém P ScreenLine 3
SL20P HORIZONTÁLNÍ ŽALUZIE technické údaje SL20P technické údaje SL20P Složení magnetu Pouzdro je ze je ze skleněného vlákna vlákna vyztuženého nylonem 66. 66. Převodovka a a přenosové součásti jsou jsou vyrobeny z z karbonové oceli oceli a pro a pro pohon pohon jsou jsou použity běžné běžné ložiska. Šnekový převod je zje z mosazi. Magnety jsou jsou vyrobeny ze ze slinutého neodymu a mají a mají následující charakteristiky: Vyrobená energie Bh Bh max-mg.0e 33-35 33-35 Zbytková indukce Br-Gauss 11.000 / / 12.000 Koercitivní síla síla Hc-Oestered 10.000 Maximální pracovní teplota C C 120 120 Curiova teplota C C 310 310 Reverzibilní teplotní faktor faktor C C -0.12% Horní Horní profil profil Extrudovaný hliník, hliník, A6063S-T5 slitina. slitina. Rozměry: šířka šířka 18 18 mm, mm, výška výška 24 24 mm mm včetně včetně volánku. Práškově lakované sladěné s s barvou lamel. lamel. Obsahuje rybinu rybinu pro pro rychlé rychlé nasazení horního profilfilu pro- do do vrchního U-profilu distančního rámečku. Lamely Hliník, Hliník, AA AA 6011-T8 slitina. slitina. Rozměry 12,5, 12,5, tloušťka 0,2 0,2 mm. mm. Vysoce odolný odolný polyesterový nastřik. Dostupné barvy: barvy: devět. devět. Lamely jsou jsou speciálně ošetřeny, aby aby se se předešlo možným únikůkům úni- chemických látek látek do do dvojskla vlivem vlivem ultrafialového záření záření a a tepelně radiace. Vlastnosti lamel lamel BARVA BARVA LEMELY LEMELY S102 S102 S106 S106 S125 S125 S130 S130 S142 S142 S149 S149 S155 S155 S156 S156 S157 S157 Solární Solární reflexe reflexe % % 70 70 62 62 57 57 58 58 65 65 68 68 42 42 65 65 43 43 Světelná reflexe reflexe % % 78 78 72 72 63 63 65 65 69 69 75 75 48 48 62 62 44 44 Solární Solární absorbce % % 31 31 38 38 43 43 42 42 35 35 32 32 59 59 35 35 57 57 Spodní profil profil Extrudovaný hliníka6063s-t5 slitina. slitina. Rozměry: šířka šířka 14 14 mm, mm, výška výška 11 11 mm. mm. Práškově lakované k k barevnému sladění s s lamelami. Vyrobeno ze ze dvou dvou do do sebe sebe uzavíratelných profilů. Žebříček Stabilizovaný 100 100 %-ní %-ní polyester. 10mm 10mm rozteč. rozteč. Mají Mají skvělou rozměrovou a a barevnou stálost stálost vůči vůči UV UV záření záření a jsou a jsou ošetřeny tak, tak, aby aby se se předešlo možným únikům chemických látek látek dovnitř dvojskla vlivem vlivem ultrafialového záření záření a tepla. a tepla. Barevně sladěny s s lamelami. Šňůry Šňůry Stabilizovaný 100%-ní polyester s s vnitřním jádrem a a skvělou rozměrovou stabilitou a a barevnou stálostí. 1,0 1,0 mm mm rozměr vnitřní vnitřní šňůry šňůry se se středovým jádrem - bílá - bílá 4 4 ScreenLine
1. technické údaje Distanční rámeček Extrudovaný hliník. Dostupný ve dvou verzích: U rámeček o rozměrech 20x6,5 mm s 2 mm křidélkem, L rámeček 20x6,5 mm s 8 mm křidélkem. Standardní knoflík Černě lakovaná mosaz s mechanickou brzdou pro případ možného poškození lamel. Pružná spojka Pružná spojka o tloušťce 3,2 mm - odolná proti zkroucení, opouzdřená v ochranném obalu samomazná pro dlouhou životnost. Možnost výběru ze tří typů knoflíků 1. standardní knoflík 2. kulatý knoflík 3. skrytý knoflík 1. 2. 3. 5
SL20P 2. rozložené schéma SL20P horizontální žaluzie SL20P rozložené schéma SL1136-SL1137 SL1138-SL1139 Pružná spojka SL1628 Převodovka SL1024 Otočný knoflík SL1029 Fixační čep spodního profilu SL1723 Silikonová trubička SL1629 Magnetický rožek SL1578 Spona ložiska SL1415 Váleček SL1155 Krytka spodního profilu SL1579 Pouzdro ložiska SL1603 Ložisko SL1196 Spodní profil SL1154 Fixační ucpávka SL1021 Šestihran 3 mm SL1537 Horní profil SL1042 Vymezovač SL1542 Extrudovaný U rámeček SL1165 Šňůra 1mm SL1197 Kryt spodního profilu SL1217 Logo SL1252 12,5mm lamela SL1199 12,5mm žebříček SL1617 Koncovka horního profilu SL1708 Plastový rožec k SL1740 Extrudovaný L rámeček 6 ScreenLine
L sklo H sklo 12,5 mm lamela SL20P dvojsklo Extrudovaný L rámeček 20 x 6.5 mm L sklo H sklo Otvory závit 2.9 mm Otvor Ø8 12,5 mm lamela SL20P sklo se standardním knoflíkem ScreenLine 7
SL20P SL20P vetrocamera dvojsklo s kulatým con pomolo knoflíkem tondo 12,5 mm lamela SL20P vetrocamera SL20P dvojsklo con se pomolo skrytým knoflíkem a scomparsa závit 2.9 mm otvor 12,5 mm lamela 8 ScreenLine
SL20P Instalace round knob kulatého assembly knoflíku SL20P Instalace standard standartního knob assembly knoflíku ScreenLine 9
SL20P hidden Instalace knob skrytého assembly knoflíku 10 ScreenLine
SL20P 3. feasibility W Width cm H 22 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 Height cm double-glazed Rozměry dvojskla unit sizes Feasible Not feasible 11
assembly postup zasklení instructions 4. ScreenLine kit components On receipt of goods, check integrity of package and confirm components as detailed on Purchase Order. The elements of the kit comprise: venetian blind with head-rail / top U shaped spacer bar (attached) / special corner keys (one with flexible coupling) altogether with factory applied silicon tubes (three) 1 No. U shaped bottom spacer bar 2 No. standard L-profile spacer bar with pins factory fixed (height) 2 No. standard corner keys standard knob control complete with flexible cable, flexible cable cover and connection. Assembly of the integral blind unit kit composition Spacer bar preparation Fill the spacer bars with the requisite amount of molecular sieve -, assemble together ensuring that the L-profile side spacer bars correctly interlock with the bottom spacer bar, and then after packing the spacer to prevent desiccant loss, butyl the three spacer bars in accordance with EN 1279-2. Remove the plastic wrap from the head-rail / blind, unwind the cords from the head-rail and keeping the slats stacked, butyl the top spacer avoiding damage or contamination to the cords during this process. assembly procedure of the spacer bar, SL20P system spacer assembly 12
assembly postup zasklení instructions Now assemble all the spacer bars to form the complete spacer frame whilst ensuring that the smallest side spacer bar is attached to the blind control corner key (silicon tubes side) and the L-profile of the side spacer is to the inner glass. Keeping the spacer frame vertical, lower the blind carefully by holding and guiding the bottom rail, taking care not to damage or contaminate the slats with butyl. Insert the bottom rail onto the retaining pin one side of the unit. Open the corner key in the opposite corner, locate the bottom rail on the second restraining pin and then close the corner key taking care to complete the butyl seal. Line assembly Pass the first glass through the washer on its base. Position the assembled blind and spacer frame on the first clean glass and ensure that it is parallel and square (no inner deflection of the vertical spacers). Press firmly to achieve good adhesion and check that there is the correct clearance between the vertical spacer and the edge of the glass on the wire drive side. During this operation avoid contact / contamination between slats and the butyl of the spacer bars. Ensure that the pelmet of the head rail is positioned against the external glass and that the slats are closed convex to the external glass. The L-profile of the side spacer bars should be to the inner glass (low E ) surface. Now assemble the clean second glass and pass through the press. unit first sealing Gas filling Following standard procedure replace the internal air with Argon. Test Prior to the final sealing it is recommended that the blind operation is checked. The unit must be vertical with the head-rail horizontal at the top of the unit. Insert a 3 mm dia. hexagonal spanner (Allen Key) in the central recess of the control corner key and check the tilting function of the slats and that the slat clearance with the spacer bar is uniform. Ensure that the three protective silicon tubes are present on the connections of the magnetic corner key (drive shaft and screw locations), in order to protect these parts during the second sealing. insertion of the blind into the spacer bars 13
assembly postup zasklení instructions Final seal Rotate the slats to their mid-position i.e. open, and apply the final seal in accordance with EN 1279-2. It is essential that the area around the wire drive connection (near the silicon tubes) is fully enclosed with sealant (additional sealant may be added by hand if necessary). The silicon tubes should be firmly fixed and must only be removed once the secondary sealant is cured. position the restraining pins into the bottom rail Preparation for the external control After polymerisation of the sealant (at least after 24 hours after the sealing procedure) remove (pull off) the silicon tubes. With a blade remove any excess sealant where the tubes have been located, in order to ensure a level surface for fixing the external drive connection. The external drive connection should then be positioned and attached square and level on the unit edge. This operation requires a particular care when centring the hexagonal pin of the wire drive attachment. The fixing screws are self-tapping and should not be overtightened. To avoid possible damage during the transportation, it is recommended that the wire drive and knob control mechanism is fitted during the IG unit installation inside the frame and. glass assembling 14
assembly postup instructions zasklení Note SL20P systems must not be inverted (vertically or horizontally) and should only be stored or moved in the vertical plane. The knob control system should be in place on the window frame prior to or during glazing. When connecting the flexible cable to the wire drive mechanism take care not to damage the drive mechanism. The transport of the integrated system must be done with the slat in open position to avoid slat contamination by the primary butyl seal which could result in sticking slats. Transport and Storage For transport and storage procedure please check the recommendations contained in the relevant part of the ScreenLine Technical Catalogue. tmelení unit second sealing 15
Screenline Pellini CZ S.p.A. a.s., via Bratislavská Fusari, 19 26845 1/6, 695 Codogno 01 Hodonín, (LO) ITALIA CZ T. + 39 420 0377 518 466411 343 614 F. + F. 39 + 0377 420 437635 518 343 info@pellini.net 613 SL20P MTL003 VYDÁNÍ Edition 07.06 www.screenline.cz www.pellini.net