Fail iolm General Information Filename: cichnova-lp.iolm Test date: 13.3.2014 Test time: 15:57 (GMT+01:00) Customer: prof. Filka Company: Studenti SSIPF Brno Operator: Petr Kormaňák Unit model: MAX-715B-M3-EA Unit S/N: 722831 Calibration date: 13.8.2013 iolm Identifiers Location A: Levý Location B: Pravý None: FIP General Information Filename: Test date: Test time: Customer: Company: Operator: FIP Identifiers Connector ID: Location: cichnova-l.cmax2 13.3.2014 15:14 (GMT+01:00) prof. Filka Unit model: FIP-420B Unit S/N: 754387 Studenti SSIPF Brno Petr Kormaňák Pravý Levý iolm Results FIP Results Table Wavelength (nm) Link length: Acquisition status: Link loss Link ORL Propagation delay (µs) 1550 0,033 46,26 --- 1310 0,145 43,96 --- 1625 0,048 46,43 --- 0,3177 km Completed iolm Pass/Fail Thresholds A: Core B: Cladding C: Adhesive D: Contact FIP Thresholds 0µm size<3µm 3µm size< 0µm size<5µm 5µm size< 0 0µm size<5µm 1 0 0 0µm size<2µm 0 0 2µm size<5µm 0 --- --- --- --- 0µm size< 0 0µm size<10µm 14 10µm size< 7 1310 nm 1550 nm Max. link loss 45,000 db 45,000 db Min. link loss 0,000 db 0,000 db Max. link ORL 15,00 db 15,00 db Max. splice loss 1,000 db 1,000 db Max. connector loss 1,000 db 1,000 db Reflectance -40,0 db -40,0 db Thr. Thr. A: Core 0µm size<3µm any 0µm size<5µm 4 3µm size< 0 B: Cladding 0µm size<5µm any 0µm size<2µm any 2µm size<5µm 5 C: Adhesive --- --- --- --- D: Contact 0µm size< any 0µm size<10µm any 10µm size< 0 Page 1 of 3
Fail iolm Test Settings FIP Test Parameters Launch fiber length: 0,5000 km Receive fiber length: 0,0000 km IOR: 1,468325 Backscatter: -81,87 db Fiber core size: 9 µm Configuration: Connector type: Fiber type: Polishing type: Focus level: IEC MM SF PC (SF) Single-Fiber connector (MM) Multiple-Mode fiber (PC) Physical contact 84.00% (Nominal) FIP Graphs A->B Page 2 of 3
Fail Link View iolm Table Element Type Position Loss Reflectance Diagnostic (km) 1310 nm 1550 nm 1310 nm 1550 nm Connector -0,5060 0,723 0,486-41,8-43,8 Connector (A) 0,0000-0,048-0,112-52,5-55,1 Connector (B) 0,3177 --- --- >-13,6 >-13,6 To characterize loss and include the element in link loss and ORL, a receive fiber is required. Element reflectance is greater than the indicated value. It is not possible to determine beyond any doubt that the value is pass. Page 3 of 3
Pass iolm General Information Filename: cichnova-pl.iolm Test date: 13.3.2014 Test time: 15:39 (GMT+01:00) Customer: prof. Filka Company: Studenti SSIPF Brno Operator: Petr Kormaňák Unit model: MAX-715B-M3-EA Unit S/N: 722831 Calibration date: 13.8.2013 iolm Identifiers Location A: Levý Location B: Pravý None: FIP General Information Filename: Test date: Test time: Customer: Company: Operator: FIP Identifiers Connector ID: Location: cichnova-p.cmax2 13.3.2014 15:16 (GMT+01:00) prof. Filka Unit model: FIP-420B Unit S/N: 754387 Studenti SSIPF Brno Petr Kormaňák Pravý Levý iolm Results FIP Results Table Wavelength (nm) Link length: Acquisition status: Link loss Link ORL Propagation delay (µs) 1550 0,259 46,18 --- 1310 0,394 44,31 --- 1625 0,368 46,92 --- 0,3174 km Completed iolm Pass/Fail Thresholds A: Core B: Cladding C: Adhesive D: Contact FIP Thresholds 0µm size<3µm 3µm size< 0µm size<5µm 5µm size< 0 0µm size<5µm 0 0 0 0µm size<2µm 0 0 2µm size<5µm 0 --- --- --- --- 0µm size< 0 0µm size<10µm 0 10µm size< 0 1310 nm 1550 nm Max. link loss 45,000 db 45,000 db Min. link loss 0,000 db 0,000 db Max. link ORL 15,00 db 15,00 db Max. splice loss 1,000 db 1,000 db Max. connector loss 1,000 db 1,000 db Reflectance -40,0 db -40,0 db Thr. Thr. A: Core 0µm size<3µm any 0µm size<5µm 4 3µm size< 0 B: Cladding 0µm size<5µm any 0µm size<2µm any 2µm size<5µm 5 C: Adhesive --- --- --- --- D: Contact 0µm size< any 0µm size<10µm any 10µm size< 0 Page 1 of 3
Pass iolm Test Settings FIP Test Parameters Launch fiber length: 0,5000 km Receive fiber length: 0,0000 km IOR: 1,468325 Backscatter: -81,87 db Fiber core size: 9 µm Configuration: Connector type: Fiber type: Polishing type: Focus level: IEC MM SF PC (SF) Single-Fiber connector (MM) Multiple-Mode fiber (PC) Physical contact 69.00% (Nominal) FIP Graphs B->A Page 2 of 3
Pass Link View iolm Table Element Type Position Loss Reflectance Diagnostic (km) 1310 nm 1550 nm 1310 nm 1550 nm Connector -0,5061 0,708 0,496-41,6-43,7 Connector (A) 0,0000 0,251 0,157-51,8-52,5 Splice 0,1489 0,044 0,011 --- --- Connector (B) 0,3174 --- --- >-13,9 >-13,7 To characterize loss and include the element in link loss and ORL, a receive fiber is required. Element reflectance is greater than the indicated value. It is not possible to determine beyond any doubt that the value is pass. Page 3 of 3
OLTS Report v4.0.3 - EXFO Electro-Optical Engineering Inc. Stránka č. 1 z 1 Protokol Informace o zakázce ID zakázky: MS Mikrotrubickovani Datum: 13.3.2014 16:25:14 Důvod: urceni viteze MS Zadavatel: PROFiber Networking Operátor A: Petr Kormanak Zákazník: prof. Filka Operátor B: Kormik Zakázka uživatele 1: mereni FTTH propoje Zakázka uživatele 2: Informace o kabelu ID kabelu: CABLE001 Pozice A: levy konektor Pozice B: pravy konektor Výrobce kabelu: OFS Typ kabelu: MiDia Breeze LT Uživatelský kabel 1: Uživatelský kabel 2: Systemové informace Přístroj A Přístroj B Jméno přístroje: FOT-932 FOT-932 Sériové číslo: 396481 414533 FasTesT ID vlákna Vlnová délka (nm) Útlum A->B Ref. A->B Útlum B->A Ref. B->A Průměr ORL A ORL B Délka (km) FIBER001 1310 0.07 1.62 0.06 1.61 0.07 >24.69 >23.63 0.317 1550 0.17 1.15 0.16 1.16 0.16 >25.77 >24.69 1625 0.29 0.74 >- 380.24 (13.3.2014 16:26:45) Studenti SSIPF Brno FIBER002 1310 0.20 1.62 0.19 1.61 0.19 >24.95 >23.87 0.314 1550 0.27 1.15 0.34 1.16 0.31 >25.99 >25.07 1625 0.31 0.74 >- 380.21 (13.3.2014 16:28:35) Fibre Optics Service, s. r. o. file:///c:/users/petr%20kormaňák/documents/olts/report/radff4b8.tmp.xml 14.4.2014